Nylon Filter Socks 4 X 14 Inches 100 Microns

• Filter socks are the best form of mechanical filtration.
• This is an essential part for wet/dry filter systems, sumps, and diy filters.
• Removes excess food, detritus, organic wastes, and other particulates to lower ammonia levels and other undesirable substances.
• Used as mechanical filtration for any sumps and diy filters.
• 100 microns.
• 1 socks per packing.

Specifications

Size: 4 × 14 in — a 4 in (about 10 cm) collar and a 14 in (about 36 cm) body. On a filter sock the first figure is always the diameter of the mouth and the second the length of the bag.
Filtration rating: 100 micron.
Material: nylon mesh.
Mouth: rigid plastic collar.
Quantity: one sock.
Our item code: NFS-100.

What the photographs on this page show: a translucent nylon monofilament mesh bag with a sewn side seam, a moulded plastic collar at the mouth and a printed fabric tag. Monofilament mesh has a precisely woven, uniform pore, which is what gives it a rated micron size in the first place.

Mesh or felt? We sell both in this size. Mesh is thinner, flows freely, clogs more slowly and washes out easily, so it lasts a long time. Felt is thicker and traps finer material at the same nominal rating, but it blinds over sooner. If you are starting out, mesh is the more forgiving of the two; if you are chasing the last of the haze out of the water, felt catches more.

100 or 200 micron? We stock this mesh in both. 200 micron is the sensible default: it catches the debris that matters, flows freely and does not need changing every other day. 100 micron — this one — polishes the water noticeably further, and pays for it by clogging roughly twice as fast. Run it when you want the water genuinely clear, after a substrate stir, or in the days following a heavy feed. Do not fit one and forget about it.

Check your sump depth before you order. At 14 in the body of this sock is two inches longer than the 4 × 12 in size a lot of sumps are built around. In a shallow first chamber a 14 in sock sits on the floor, which stops it draining freely and makes it clog faster. Measure from the underside of your sock holder to the bottom of the chamber; you want a few inches of clearance.

Setup & Use

Where it goes: in the first chamber of your sump, directly under the drain from the display, so every drop coming down the overflow passes through it before it reaches your skimmer, media and return pump. That is the whole point — the sock takes the solids out while they are still solids, instead of letting them break down into ammonia and nitrate in the sump.

You need something to hang it from. A filter sock is not self-supporting — the 4 in collar has to sit in a holder or a moulded sump shelf, with the drain line discharging into the mouth. We stock acrylic sock holders in single and double versions; the double lets you swap one sock while the other keeps working, which is the difference between a five-minute job and a wet floor. If your sump already has a sock bracket, check it takes a 4 in ring — most do, because 4 in is the near-universal collar size.

Fitting it: drop the collar into the holder, check that the drain line ends inside the mouth of the sock rather than above it or against the fabric, and make sure the bag hangs free rather than resting against the chamber wall. A sock pressed against acrylic uses only half its area.

At 100 micron, expect to be busy. This is the fine one. On a well fed tank it can blind over in a day or two, so if you cannot change it that often, use the 200 micron version for daily duty and keep this one for polishing.

Changing it — our advice, not a manufacturer instruction. There is no manufacturer schedule for this product because there is no brand behind it. In practice a sock at this fineness on a normally stocked tank needs changing every two to four days. You are not waiting for it to look dirty; you are changing it before the trapped detritus starts breaking down inside it. A sock left in place for a fortnight stops being mechanical filtration and becomes a nitrate source sitting in your highest-flow chamber.

The other reason to change it on time: a clogged sock does not stop the water, it just makes it go round. Once the fabric blinds over, the sock fills and overflows the collar, and everything you were trying to catch goes straight into the sump unfiltered — usually without any obvious sign that it has happened.

Washing and reusing. Rinse it under a tap the moment it comes out, before the detritus dries into the fabric — inside out, from the clean side, so you push the muck out rather than deeper in. It can then go through a washing machine on a cold cycle with no detergent, no fabric softener and no bleach; softener coats the fibres and closes the pores, and detergent residue goes straight into your tank next time. Dry it completely before storing. Buy at least two so one is always ready.

When to throw it away: when the seam opens, when the collar cracks, or when it no longer flows freely after washing. A sock that bypasses at the seam is doing nothing at all.

One thing worth knowing if you keep corals. Mechanical filtration this fine removes suspended particles indiscriminately, and some of those particles are food. Many reef keepers run socks continuously and feed accordingly; others run them for a day or two after a big feed or a stir-up and leave them out the rest of the time. Both work. What does not work is leaving a dirty one in.

Freshness & Storage

Every batch we dispatch carries a minimum of 6 months’ remaining shelf life. Store this product in a cool, dry place away from direct sunlight, with the cap or inner foil closed tightly after each use.

Filter media and substrates carry no manufacturing or expiry date — their working life begins on first contact with water, not on the shelf.

Returns & Replacement

Returns are accepted within 7 days of delivery, provided the item is unused and in its original packaging. Manufacturer-sealed items cannot be returned once the seal is broken, and sale-priced items are not refundable.

If your item arrives defective or damaged, message us on WhatsApp with your order number, or email us if you would rather, and we will replace it. Approved replacements are delivered within 3 to 5 business days. Transit damage is covered by insurance on every shipment. If tracking shows delivered but nothing reached you, tell us within 72 hours, which is the reporting window Indian couriers allow. Damage caused during installation or use is not covered; replacement spares for such cases are chargeable.

Full terms are on our Cancellation & Returns page.